- Year:
- 2003
- Length:
- 42
- Hull:
- Steel
- Builder:
- Taylor Enterprises
- Location:
- Washington
42’x12’ steel utility barge built by Taylor Enterprises (WA) in 2003. Used for habit restoration. 2003 Mercury 90 HP outboard motor. Steel pontoons w/ virgin polyethylene foam. Steel diamond plate deck. Steel pilot house and gantry. Gantry supports 1 ton, electric,...
More Details- Year:
- 1985
- Length:
- 26
- Hull:
- Fiberglass
- Builder:
- Miller
- Location:
- Alaska
26’x10’ fiberglass bowpicker built in 1985 by Miller. Kodiak Marine 496 main rated at 390 hp with Hamilton 1031 jet. Makes 31 knots. Packs 4800# in (1) fish hold. (2) station helm with SeaStar steering and morse controls. Bennet trim tabs. Reel w/ twister drive an...
More Details- Year:
- 1982
- Length:
- 32
- Hull:
- Fiberglass
- Builder:
- Wegley
- Location:
- Alaska
32’x13’ fiberglass, Jumbo Wegley built in 1982. Repowered in 2016 w/ Cummins 6CTA rated at 430 hp w/ ZF280 gear. PacWest 7.5 ton RSW. Packs 14k lbs in (10) high density foam, insulated fish holds. Updated flush deck, fish holds, deck equipment, anchor deck, and wind...
More Details- Year:
- 1974
- Length:
- 64
- Hull:
- Aluminum
- Builder:
- Matsumoto Shipyards
- Location:
- Alaska
64’x17.5’x8’ aluminum Canadian seiner set up to tender salmon. Built by Matsumoto Shipyards in 1974. Cat 3406 rated at 265 hp w/ Twin Disc MG514 gear. Packs 90k lbs combined in (2) fiberglass fish holds. Cold Sea 40 ton RSW w/ 35 hp compressor and all new circ plumb...
More Details- Year:
- 1989
- Length:
- 32
- Hull:
- Aluminum
- Builder:
- Kvichak
- Location:
- Alaska
32’x13.5’ aluminum Bristol Bay boat built by Kvichak in 1989. Repowered in 2022 w/ John Deere 6090 SFM85 rated at 550 hp and new ZF305-3A gear. Packs 13k lbs floating in (7) updated fish holds w/ false bottoms. 7.5 ton Pac West RSW. Fixed Maritim...
More Details- Year:
- 1975
- Length:
- 108
- Hull:
- Steel
- Builder:
- Marco
- Location:
- Washington
108’x27’x9’ steel crabber built by Marco in 1975. Vessel sunk and salvaged in 2024. Reported to pack approximately 360k# pinks in 7,500 cu ft. Machinery and electronics are presumed to not be operable. Asking $100,000, make offers. ******Additional Terms******* V...
More Details- Year:
- 1980
- Length:
- 32
- Hull:
- Aluminum
- Builder:
- Marco
- Location:
- Alaska
32’x12’x2.5’ aluminum, flush deck, RSW, Bristol Bay gillnetter built by Marco in 1980. John Deere 6068 rated at 210 hp w/ Twin Disc 506 gear. Diesel drive PacWest 6 ton RSW system w/ 2.5 kW generator. Packs 10k lbs in (8) newly insulated fish holds. Maritime Fa...
More Details- Year:
- 1973
- Length:
- 40
- Hull:
- Aluminum
- Builder:
- Elmer W. McEachern
- Location:
- Oregon
40’x11.9’x4.8’ aluminum troller built by Elmer W. McEachern (BC) in 1973. John Deere 6068 rated at 210 hp w/ Twin Disc MG550 gear. Packs 10k lbs in (1) newly fiberglassed and insulated fish hold. Crab insert, davit, picking boom, hay rack, (4) single spool gurdies, p...
More Details- Year:
- 1978
- Length:
- 32
- Hull:
- Fiberglass
- Builder:
- Modutech
- Location:
- Alaska
32’x12’x2’ fiberglass, flush deck Bristol Bay boat built by Modutech in 1978. Volvo TAMD70C main rated at 280 hp, w/ only 600 hours after 2019 rebuild. Fuel capacity of 300 gallons in (2) aluminum tanks. Vickers dual belt driven hydraulic pump. Packs 10,000 lbs in (...
More Details- Year:
- 1970
- Length:
- 32
- Hull:
- Aluminum
- Builder:
- Matsumoto
- Location:
- Alaska
32’ aluminum Bristol Bay gillnetter built by Matsumoto in 1970 and rebuilt in 1983. Crusaider 454 gas engine w/ approx 350 hp. Aluminum reel, levelwind and anchor winch. Packs 12,000 lbs in (7) aluminum fish holds. (3) steering stations. Includes contents of locker...
More Details- Year:
- 1975
- Length:
- 36
- Hull:
- Fiberglass
- Builder:
- BLRL Marine
- Location:
- Washington
36’x12’x5’ fiberglass geoduck dive boat built by BLRL Marine in 1975. CAT 3208 main rated at 210 hp, w/ 905 hours. Twin Disc 506 gear. Fuel capacity of 300 gallons in (2) tanks. (2) Honda Gx 340 generators. Packs 12 tons in (4) fish holds. Includes hydraulic davit...
More Details- Year:
- 1979
- Length:
- 40
- Hull:
- Fiberglass
- Builder:
- Beck
- Location:
- Washington
40’x13’ fiberglass dive boat/crabber built by Beck in 1979. GMC 671 main engine rated at 250 hp. 750 gallons fuel capacity. Packs estimated 20k# in one fish hold. Tophouse design. (2) davits on deck. Accommodations include (4) berths, kitchen, and marine head. Re...
More Details- Year:
- 1991
- Length:
- 88
- Hull:
- Steel
- Builder:
- D&T Marine
- Location:
- Hawaii
88’x22.5’ steel tuna vessel built by D&T Marine in 1991. Cummins KTA1150 main engine rated at 500 hp. Twin Disc MGX516 with 6:1 ratio. 8.5 knot cruise. Twin 60 kW Cummins 6BT gen sets, (1) 30 kW Cummins 4B gen set. 14k gallons fuel capacity in (10) tanks. (4) fish...
More Details- Year:
- 1967
- Length:
- 92
- Hull:
- Steel
- Builder:
- Pac Fish
- Location:
- Washington
92’x26’ steel crabber built in 1967 by Pac Fish. Twin Caterpillar 3406B main engines rated at 360 hp each. Twin Disc MG-5140 gears with 4.5:1 ratio. (2) 190 kW Caterpillar 3306B gen sets, 20 kW Isuzu hotel gen set. Packs 275k# reds, 130k# crab in (2) fish holds. 80...
More Details- Year:
- 1974
- Length:
- 38
- Hull:
- Fiberglass
- Builder:
- Delta
- Location:
- Alaska
38’x13’ fiberglass gillnet/crab/shrimp vessel built in 1974 by Delta. Volvo TAMD61A main engine rated at 301 hp. Twin Disc MG-509 gear with 2:1 ratio. Burns 5 gph at 7.5 knots. 10 kW Isuzu LB31 gen set. Packs 15k# in (4) insulated fish holds. Deck equipment includ...
More Details- Year:
- 1976
- Length:
- 42
- Hull:
- Fiberglass
- Builder:
- Delta
- Location:
- Alaska
42’x13’ fiberglass seiner/crabber built by Delta in 1976, overhauled in 2013-14. John Deere 6090 main engine rated at 330 hp. Twin Disc gear with 2.5:1 ratio. Burns 3.5 gph at 7 knots. 18 kW Mitsubishi gen set. Packs 28k# salmon. IMS 12.5 ton RSW system. Vickers...
More Details- Year:
- 1976
- Length:
- 38
- Hull:
- Fiberglass
- Builder:
- Delta
- Location:
- California
38’x13.5’x5.4’ fiberglass Delta crabber/troller built in 1976. John Deere 6068 rated at 240 hp w/ Twin Disc 506 gear. Fuel capacity of 740 gallons in (4) tanks. Single tanked fish hold and two tank inserts - crab insert packs 6,100 lbs and insulated salmon insert pac...
More Details- Year:
- 1968
- Length:
- 36
- Hull:
- Aluminum
- Builder:
- McQen
- Location:
- Washington
36’x12’x2’ aluminum, crabber, Monk design, hull built by McQen in 1968. Hull stored inside, under cover until finished in 2018. Makes 32 knots. Recently installed Volvo D6 rated at 370 hp, w/ apprx 1400 hrs. Humbyrd 15” crab block and hydraulic davit. 16 GPH hydrau...
More Details- Year:
- 1976
- Length:
- 37
- Hull:
- Aluminum
- Builder:
- Freeman Marine
- Location:
- Oregon
37.6’x13.5’x5.5’ aluminum vessel built by Freeman Marine in 1976, rigged for crab, troll, and tuna. John Deere 6068 main rated at 260 hp w/ Twin Disc gear. Isuzu 21kw genset. Fuel capacity of 1,000 gallons in (2) tanks. Packs 8,600 lbs in (2) fish holds below deck,...
More Details- Year:
- 1970
- Length:
- 36
- Hull:
- Fiberglass
- Builder:
- Roberts
- Location:
- Washington
36’x12.5’x3.5’ fiberglass gillnetter built by Roberts in 1970. CAT 3126b main rated at 450. ZF reduction gear, new in 2019. Fuel capacity of 400 gallons in (2) tanks. Packs 10,000 lbs in (5) tanked and insulated fish holds. Deck equipment includes gillnet reel, lev...
More Details- Year:
- 1980
- Length:
- 32
- Hull:
- Aluminum
- Builder:
- Marco
- Location:
- Alaska
32’x11.5’x2.5’ aluminum, RSW, flush deck, Bristol Bay gillnetter built by Marco in 1980. 2015 Yanmar 6LY rated at 440 hp w/ ZF360 gear. Makes 14 knots. Bow thruster. IMS 7.5 ton RSW system. Packs 11k lbs in double walled fish holds w/ insulation. Maritime Fab. re...
More Details- Year:
- 1985
- Length:
- 32
- Hull:
- Fiberglass
- Builder:
- Radon
- Location:
- California
32’x10’x3.6’ fiberglass Radon built in 1985, rigged for crab and salmon. Twin GM 383 gas engines rated at 250hp each. Does 20kts. Fuel capacity of 250 gallons in one tank. Fish hold packs 1,600 lbs crab. Deck equipment includes crab block, davit, boom w/ winch, sal...
More Details- Year:
- 1992
- Length:
- 58
- Hull:
- Steel
- Builder:
- Bill Berggren
- Location:
- California
58’x21’x10.5’ steel seiner package w/ skiff and permits, built in 1992 by Bill Berggren. Cummins KTA-19 main rated at 500 hp w/ Twin Disc reduction gear. Northern Lights 60kw and Northern Lights 30kw gensets. 20-ton RSW system w/ titanium chillers. Pakcs 116,000 lbs...
More Details- Year:
- 1994
- Length:
- 58
- Hull:
- Steel
- Builder:
- Van Peer Boat Works
- Location:
- Alaska
58’x23’x10’ steel combination seiner/pot/LL/trawler built by Van Peer in 1994. Extensive shipyard at Platypus in 2018. Yanmar 6AYM-FT main rated at 755 hp, new in 2018. Twin Disc MG5222 gear w/ 6:1 ratio. John Deere 99 kW and Kubota 28 kW gensets both new in 2018. P...
More Details- Year:
- 1979
- Length:
- 42
- Hull:
- Fiberglass
- Builder:
- SeaMaster
- Location:
- Alaska
42’x12.5’ fiberglass troller built in 1979 by SeaMaster. GMC 471 main engine rated at 120 hp. Twin Disc gear with 3.83:1 ratio. Makes 7.5 knots, 1k gallons fuel capacity. Eaton 421 hydraulics. Packs 9500# frozen coho (1) fish hold, plate freezer system. Includes E...
More Details- Year:
- 1995
- Length:
- 58
- Hull:
- Steel
- Builder:
- Studeman
- Location:
- Oregon
58’x20’x9.5’ steel combination vessel built in Reedsport, OR by Scott Studeman in 1995. John Deere 6135 main rated at 425hp w/ Twin Disc 5114 gear. (2) John Deere 4045 65kw gensets. Fish hold w/ removable partitions packs 33,000 lbs crab w/ aft section as bait freeze...
More Details- Year:
- 1973
- Length:
- 38
- Hull:
- Wood
- Builder:
- Sather
- Location:
- Alaska
38’x11’x5.5’ wooden salmon troller built by Sather (BC) in 1973. Updated John Deere 4045 TFM rated at 135 hp w/ ZF-63 gear w/ 1:2.4 ratio. Packs approx. 4.8 tons in single fish hold. Kolstrand 3-spool gurdies, picking boom w/ electric winch. Vickers V20 hydraulic pu...
More Details- Year:
- 1989
- Length:
- 32
- Hull:
- Fiberglass
- Builder:
- Wegley
- Location:
- Alaska
32’x13’ fiberglass Jumbo Wegley buiit in 1989. Cummins QSC main engine rated at 550 hp, low hours on rebuild. Twin Disc gear with 2:1 ratio. Makes 12 knots. Packs 15k# in (12) insulated holds. IMS 7.5 ton RSW system. Deck equipment incudes Maritime Fab reel and Ki...
More Details- Year:
- 2018
- Length:
- 33
- Hull:
- Aluminum
- Builder:
- ACI
- Location:
- Washington
33’x11’x2’ aluminum crabber built by ACI in 2018. Twin Honda 250hp outboards. Cruises at 22kts and does 40kts WOT. Fuel capacity of 200 gallons in (2) tanks. 13hp power pack w/ 30 gallon hydraulic tank. 15” Junes crab block, hydraulic davit, and dump box. Fish hold...
More Details- Year:
- 1978
- Length:
- 32
- Hull:
- Fiberglass
- Builder:
- Roberts
- Location:
- Alaska
32’x11.5’ fiberglass sternpicker built in 1978 by Roberts. Volvo TAMC70D main engine rated at 260 hp, low hours on rebuild. Twin Disc gear with 2:1 ratio. Packs 9k# in (6) insulated fish holds. Deck equipment includes Maritime Fab drum, levelwind, rower roller, and...
More Details