TE19-012

$2,000,000
Year:
1991
Length:
106
Hull:
Steel
Builder:
LaForce Shipyard
Location:
Washington

TE19-012

106’x26’x10’ steel crabber/tender, built by LaForce Shipyard in 1991. Twin 500 hp John Deere 6135 mains, each w/ Twin Disc 516 gears, all new in 2017. (2) 175kw John Deere 6081 gensets. Packs 400k pounds in (3) insulated holds, w/ 60 ton RSW system. Walk-in bait fre...

More Details

SE19-018

$399,000
Year:
1978
Length:
48
Hull:
Fiberglass
Builder:
Delta
Location:
Washington

SE19-018

48’x14’x4’ fiberglass seiner built by Delta in 1978, lengthened and overhauled in 2015. Volvo TMD 120A main engine rated at 320 hp. Twin Disc 509 gear with 2:1 ratio. 30 kW Mitsubishi genset. Packs 45k# in (2) insulated holds. IMS 18 ton RSW system, new in 2015. D...

More Details

CO19-028

$375,000
Year:
1998
Length:
45
Hull:
Fiberglass
Builder:
Kings Point Marine
Location:
Alaska

CO19-028

45’x18’x9.6’ fiberglass combination seiner/crabber built in 1998 by Kings Point Marine in Newfoundland. Volvo TAMD 122A inline 6 cylinder w/ Twin Disc MG511 gear. Isuzu 25kW genset. 15 ton RSW w/ titanium chiller, new in 2013. Packs 70k lbs total in (2) insulated fi...

More Details

CO19-027

$1,350,000
Year:
1975
Length:
100
Hull:
Steel
Builder:
Bender
Location:
Alaska

CO19-027

100’x24’x11’ steel combination tender/crab/pot boat built by Bender in 1975. Cat D398 rated at 850 hp w/ Cat 7271 marine gear. (2) New John Deere 99 kW and 156 kW gensets. Updated IMS 50 ton RSW system w/ new piping. Packs 250k lbs in (2) insulated fish holds. Yaqu...

More Details

CR19-038

$310,000
Year:
2019
Length:
34
Hull:
Aluminum
Builder:
Velocity Marine
Location:
Washington

CR19-038

34’x12’ new aluminum crabber, built by Velocity Marine and delivered in 2019. Twin 350 hp Suzuki outboards w/ only 250 hours on each. Cruises at 30 mph, 50 mph WOT. Bow thruster. Fuel capacity of 300 gal. 13 hp Honda power pack runs 11gpm hydraulic pump. Tanked h...

More Details

CR19-037

$235,000
Year:
2016
Length:
32
Hull:
Aluminum
Builder:
Hard Drive Marine
Location:
California

CR19-037

32’x11.8’x2’ aluminum crabber/combination vessel, built by Hard Drive Marine in 2016. Dual Yamaha F300NCA outdrives w/ 1,600 hours and new lower units in 2019. Fuel capacity of 300 gallons. 30kt cruise at 4,400 rpm, burning 1.2 gph total. 13hp Honda power pack w/ re...

More Details

CO19-026

$780,000
Year:
2014
Length:
50
Hull:
Fiberglass
Builder:
Maritime Fab
Location:
Alaska

CO19-026

50’x18’ fiberglass combination crab/shrimp/tender built by Maritime Fab in 2014. Scania D112 rated at 650 hp w/ ZF 360 reduction gear. MER MG 18 kW genset. (4) tankable fish holds pack 60,000 lbs combined. 6 ton electric RSW system. Main boom w/ (3) winches, single...

More Details

TR19-043

$70,000
Year:
1993
Length:
27
Hull:
Fiberglass
Builder:
Skipjack
Location:
California

TR19-043

27’x8.25’x3’ fiberglass troller/crabber built by Skipjack in 1993. Isuzu 6BG1T rated at 174 hp. BW Velvet Drive w/ 2:1 gear reduction. Single fish hold w/ freon holding coils. Hasbra (3) spool gurdies, trolling poles and 10” Hydro Slave pot hauler. Vickers hydrauli...

More Details

TR19-044

$34,000
Year:
1974
Length:
32
Hull:
Fiberglass
Builder:
Pettis
Location:
Washington

TR19-044

32’ fiberglass troller/longliner/crabber built in 1974 by Pettis. John Deere 6068 main engine. Microcommander 3-station controllers. 3-spool Simplex gurdies, tuna puller, and additional gear. New Dickinson stove. Electronics include VHF and Furuno radar, plotter, s...

More Details

TR19-042

$135,000
Year:
1973
Length:
36
Hull:
Fiberglass
Builder:
Roberts
Location:
Alaska

TR19-042

36’x11’x4’ fiberglass troller built in 1973 by Roberts in La Conner, WA. John Deere 6068 main engine rated at 210 hp. Twin Disc 506 gear. Makes 7.5 knots. 300 gallons fuel capacity in (2) tanks. Packs appx 3,500# in (2) holds. Recently reconditioned Kolstrand 3-sp...

More Details

SE19-016

$1,750,000
Year:
1981
Length:
58
Hull:
Steel
Builder:
Hansen
Location:
Alaska

SE19-016

58’x22.5’x10 steel combination vessel, rigged for seine and pots, built by Hansen in 1981. CAT C18 main rated at 600 hp w/ Twin Disc quick-shift gear. 100kw John Deere 6068 and 21kw John Deere 4024 gensets. (2) 20-ton RSW systems. Packs 135,000# in (2) holds. Deck...

More Details

SE19-015

$375,000
Year:
1969
Length:
56
Hull:
Wood
Builder:
Jones-Goodell
Location:
Washington

SE19-015

56’x15.5’x8’ wood combination vessel, rigged for seine, built by Jones-Goodell in 1969. John Deere 6081 main rated at 335 hp w/ Twin Disc 514 gear. 40kW John Deere and 6.5kW Hyundai gensets. Hydraulic pumps off main (40/25 gpm) and big aux (20 gpm). Almost new RSW s...

More Details

CR19-036

$205,000
Year:
1984
Length:
32
Hull:
Aluminum
Builder:
La Conner
Location:
Alaska

CR19-036

32’x14’x3’ aluminum crabber/longliner combination vessel built by La Conner in 1984. Twin Cummins 6BTA main engines rated at 315 hp each. ZF 2-20 AS gears. Yamaha EF2600 110v portable generator. Deck equipment includes Maritime Fab roller, longline reel with levelwi...

More Details

RS19-004

$350,000
Year:
1980
Length:
72
Hull:
Fiberglass
Builder:
Kelly-Wesport
Location:
Washington

RS19-004

72’x18.5’x7.5’ fiberglass vessel built by Kelly-Westport in 1980. Twin GMC 12V71 main engines rated at 500 hp each. Twin Disc MG 514 gears with 2.5:1 ratio. Makes 12 knots. 9 kW Northern Lights genset. 1,800 gallons fuel capacity. HIAB 3,000# crane and Capstan pede...

More Details

UT19-006

$75,000
Year:
1991
Length:
33
Hull:
Aluminum
Location:
Washington

UT19-006

33’x10’x3’ aluminum utility vessel, rigged as oil response boat, built in 1991. CAT 3208 main rated at 210 hp w/ less than 300 hours. Makes 12 knots. Spray foam insulated cabin and forepeak w/ (2) berths. Tow post on deck and forward push knees. Garmin combo unit w...

More Details

CR19-035

$10,000
Year:
1991
Length:
25
Hull:
Fiberglass
Builder:
Pelsu
Location:
California

CR19-035

25’x7.9’x2’ fiberglass skiff, built in 1990. 390 hp Mercruiser 7.4 liter Bravo Three gas engine w/ 1,300 hours. Top speed of 36 knots. Hydraulic steering. 150 gallon fuel tank. (6) fishing poles, and lots of misc gear. Electronics include GPS, VHF, Hummingbird LCR...

More Details

PL19-009

$167,800
Year:
2017
Length:
30
Hull:
Aluminum
Builder:
LSC Performance
Location:
Washington

PL19-009

30’x10.5’x2.5’ aluminum sport boat built by LSC Performance in 2017. Twin Suziki 300 hp outboards w/ approx 315 hours each. Cruises at 35 mph. (1) fuel tank w/ 285 gallons capacity. Ready to fish Puget Sound with crab davit, electric block, and wash down pump. Elec...

More Details

DR19-009

$600,000
Year:
1976
Length:
63
Hull:
Steel
Builder:
Mike Brown
Location:
Oregon

DR19-009

63’x17.7’x8’ steel combination vessel, rigged for bottom trawling, built by Mike Brown in Port Hueneme, CA. Isuzu UM6WG main rated at 505 hp and Twin Disc 514 gear. PTO drives (2) 60 gpm pumps. John Deere 40 kW genset w/ Vickers 20 gpm pump. Packs 70,000# iced groun...

More Details

CO19-023

$775,000
Year:
1983
Length:
56
Hull:
Steel
Builder:
Frank James
Location:
Alaska

CO19-023

56’x19’x8’ steel combination vessel built in 1983 by Frank James. Cummins QSL9 main engine rated at 440 hp. Twin Disc 509 gear with 4:1 ratio. Northern Lights 10 kW and Cummins 40 kW gensets. Packs 66k# in (2) fish holds. 15 ton RSW system. Aluminum bait house, li...

More Details

CR19-033

$399,000
Year:
1978
Length:
56
Hull:
Steel
Builder:
Wayne Gray
Location:
Washington

CR19-033

56’x19.2’x6.3’ steel crabber/tender, built by Wayne Gray in 1978. Deck extended by 4’ fantail on stern. Cummins N-14 main rated at 450 hp. Twin Disc 514 gear. 65 kW John Deere genset w/ Pitts electric clutch and 25 gpm Vickers pump. 3,000 gallons fuel capacity. 25...

More Details

CR17-034

$325,000
Year:
1979
Length:
42
Hull:
Fiberglass
Builder:
Delta
Location:
Washington

CR17-034

42’x14’x3.5’ fiberglass crabber/seiner built by Delta in 1979, complete refit and tophouse added in 2012. Cummins 6CTA main rated at 255 hp, w/ 2,500 hours. Twin Disc 509 gear. 15 kw Isuzu genset w/ 2,800 hrs. Tanked fish hold packs 10,000 lbs crab. Deck equipment...

More Details

CR19-032

$1,900,000
Year:
1979
Length:
109
Hull:
Steel
Builder:
MD Phares Boat Construction
Location:
Alaska

CR19-032

109’x30’x14’ steel crabber/tender built by M.D. Phares Boat Construction in 1979. Twin CAT 3412 main engines, each rated at 650 hp, rebuilt in 2019. ZF 3710 gears with 5.952:1 ratio. 185 kW John Deere 6090L, 65 kW CAT 3306 gensets, Perkins hotel unit. Makes 10 knots...

More Details

CR14-009

$125,500
Year:
2004
Length:
32
Hull:
Aluminum
Builder:
Western Fabrication
Location:
Washington

CR14-009

32’x10’x3’ combination crab/longline/tuna vessel built in 2004 by Western Fabrication. Volvo Penta D4 main rated at 225 hp with low hours. Duoprop outdrive recently serviced. Honda 9.9 trolling motor. 120 gallon fuel capacity. Tuna poles, longline chute, crab block...

More Details

TR19-038

$235,000
Year:
1987
Length:
37
Hull:
Fiberglass
Builder:
Wegley
Location:
Washington

TR19-038

37’x13’x5’ fiberglass combination vessel built by Wegley in 1987. Lugger 6125 main engine rated at 440 hp. Twin Disc 508 gear with 1.52:1 ratio. Isuzu 4kW genset. 650 gallons total fuel capacity including saddle tanks. Packs 18k# in (1) insulated fish hold. Crab i...

More Details

CO19-022

$450,000
Year:
1997
Length:
40
Hull:
Aluminum
Builder:
Curry
Location:
Alaska

CO19-022

40’x14’x6’ aluminum combination crab/gillnet/charter/research boat built by Curry/Petrazelka in 2007. Twin Volvo D-6 350 hp diesels w/ outdrives. Cruise at 22 kts and 32 kts top speed. Westerbeke 7.6 kw auxiliary. Twin Vickers 20 GPM hydraulic pumps w/ clutch. Warr...

More Details

CR19-031

$1,800,000
Year:
1978
Length:
76
Hull:
Steel
Builder:
Carl Berg
Location:
Washington

CR19-031

76’x22’x12’ steel crabber/tender built in 1978 by Carl Berg. Isuzu main engine rated at 600 hp. Twin Disc 514C gear with 6:1 ratio. 65 kW John Deere 4045, 42 kW Lugger gensets. Packs 165k# in (3) fish holds. 30 ton RSW system. Electronics include (2) VHF, (2) GPS,...

More Details

CR19-030

$85,000
Year:
1966
Length:
58
Hull:
Steel
Builder:
unknown
Location:
Alaska

CR19-030

58’x18’x7.5’ steel crabber/longliner built in 1966. GMC 8V71 main engine rated at 318 hp. Allison gear with 4.5:1 ratio. Kubota 27 kW genset. 3k gallons fuel capacity in (2) tanks. Packs 70k# of fish in (2) holds. Deck equipment includes a boom with hydraulic winc...

More Details

TR19-035

$115,000
Year:
1946
Length:
46
Hull:
Wood
Builder:
Tongass Marine
Location:
Alaska

TR19-035

47’x14.3’x6’ wood freezer troller, built in 1946. GMC 6-71N rated at 180 hp, w/ Capitol gear. Heavily insulated hold of 1500 cu ft capacity with 10 ton blast freeze system. Electronics include VHF, SSB, GPS Furuno radar, ComNav pilot w/ 2 remotes. Hydraulic steering...

More Details

CR19-029

$480,000
Year:
1981
Length:
40.9
Hull:
Fiberglass
Builder:
American Commercial
Location:
California

CR19-029

40.9’x13.9’x6’ fiberglass crabber/troller, built by American Commercial in 1981. Detroit 671 main rated at 174 hp. Twin Disc 506 gear. New portable Honda 3000 generator. 1,600 gal fuel capacity in (2) tanks. Packs 8 tons salmon and 6,400 crab in aluminum insert. S...

More Details

TR19-036

$340,000
Year:
1928
Length:
46
Hull:
Wood
Builder:
Strom & Orum
Location:
California

TR19-036

46’x13’x7’ wood troller/crabber with permits, built in 1928 by Strom and Orum in Tacoma, WA. Detroit 671 main rated at 165 hp, w/ 2,500 rebuilt hrs. Twin Disc 509 gear. Perkins 7.5 kW genset. Fish hold packs 24,000# not tanked, 8,500# in crab instert, and 5,000# sal...

More Details

Sign up for email updates