Crabbers[46 listings]

Click here to be notified of updates to the Crabbers pagewatch helphelp

Vessels 1 - 46 of 46
$1,100,000
thumbnail CR15-022  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1989    Length: 58    Hull: Fiberglass    Builder: Hansen    Location: Alaska
58'x17'x7' fiberglass seiner built by Hansen in 1989. Lugger L6140A 550 hp main with Twin Disk 511 2:1 gear. Packs 100k lbs in (2) insulated RSW fish holds. (2) gen sets. 2,200 gallon fuel and 600 gallon water capacities. Electronics include radar, GPS, sounder, plotter, (2) VHF, SSB, two meter, auto pilot, and computer. Asking $1,100,000.
$850,000
thumbnail CR15-021  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1988    Length: 54    Hull: Fiberglass    Builder: LeClercq    Location: Alaska
54'x15'x7' fiberglass seiner built by LeClercq in 1988. Twin Lugger 614TA 550hp mains with Twin Disk 511 gears. (3) fuel tanks with a total capacity of 1,600 gallons. (2) water tanks with total capacity of 450 gallons. (2) fish holds with a total capacity of 45,000 lbs in RSW. Electronics include radar, sonar, (2) GPS, sounder plotter, (2) SSB, VHF, CB, auto pilot, and computer. Asking $850,000.
$139,000
thumbnail CR15-020  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1961    Length: 34    Hull: Aluminum    Builder: Matsumoto    Location: Washington
34'x11' coastal crabber built by Matsumoto in 1961. 454 Chev Crusader main engine. Borg Warner 2.57:1 gear. 8 knot cruise 15 knot WOT. 17" Junes crab block. 100 fully rigged pots. New triple axle boat trailer. Electronics include GPS, VHF, radar, and sounder. California tier 7, 175 pot, crab permit included. Asking $139,000.
$30,000
thumbnail CR15-019  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1987    Length: 26    Hull: Fiberglass    Builder: home built    Location: Washington
26'x9'x2.5' fiberglass combination skiff built in 1987. 270 Crusader gas main with a new propellor. 350 Mercrusier spare main. 100 gallon aluminum fuel tank. 15 knot cruise. Fuel tanks, Aft deck, and gunnels new in 2009. Aluminum crab davit, 12" block and spare propellor. V berth provides storage. Electronics include Raytheon sounder, plotter and radar all in one. 8'x11.6" of open deck. Galvanized tandem axle trailer with surge brakes and new tires. Asking $30,000.
$300,000
thumbnail CR15-018  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1981    Length: 42    Hull: Fiberglass    Builder: LeClercq    Location: California
42'x15'x4' fiberglass pocket seiner built by Leclerq in 1981. John Deere 6068 AFM85 250hp main, installed 2014, with Twin Disk 507 2:1 gear. Yukon Power Systems 40 kw aux installed 2014. Currently rigged as light/brail boat for California squid fishery. Call for complete survey. Asking $300,000 for boat alone or $500,000 with squid light/brail permit.
$445,000
thumbnail CR15-017  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1979    Length: 41.5    Hull: Fiberglass    Builder: Modutech    Location: Oregon
41.5'x11.5'x5' fiberglass crabber/troller, built in 1979 by Modutech. Partially enclosed tophouse. GMC 6V92 rated at 300 hp, 7.5 kw Whisper Watt gen set. Bait chopper, 17" crab block on davit, and 3 spool Simplex gurdies. Electronics include (2) GPS, (2) VHF, radar, (2) sounders, plotter, and ComNav autopilot. 4-man liferaft. Comes WITH 250 pot CA crab, 300 pot OR crab, and OR salmon troll licenses. Asking $445,000.
$1,750,000
thumbnail CR15-016  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 2001    Length: 76    Hull: Steel    Builder: Wahl    Location: Alaska
76'x30'x12' steel combination freezer/RSW vessel, rigged for pots, longline, and tendering. Built by Wahl in 2001. Cat 3412 main rated at 720 hp. (2) Cat 3306 190 kw and (1) Deere 65 kw gen sets. Mustad Autoline system. Full shelter deck. Well-insulated holds are equipped with freezer coils (200,000#) or RSW (300,000#) with 50 ton compressor. Bait hold, ice machine, and watermaker. Deck crane and cargo boom. Complete electronics. Unique vessel provides lots of opportunity. Call for details. Asking $1,750,000.
$100,000
thumbnail CR15-014  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1976    Length: 37.7    Hull: Fiberglass    Builder: Westport Shipyard    Location: Washington
37.7'x11.8'x4.6' Puget Sound dive vessel built in 1976 by Westport Shipyard Inc. Low hours on a Volvo TAMD 74E main rated at 450 hp. Twin Disc gear. 17 knot @ WOT, 12 knot cruise. Quincy 325 dive compressor. Aluminum 300 gallon fuel capacity. Electronics include (2) VHF, Furuno color sounder and Furuno 32 mile radar. Nice clean vessel, turnkey, ready to work. Price reduced to $100,000.
$485,000
thumbnail CR15-013  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 2015    Length: 50    Hull: Steel    Location: California
50'x16'x6.6' new construction combination crab/troll vessel. John Deere 6068 main rated at 201 hp. Twin Disc MG 5061 gear. Monel tail shaft. 2,000 fuel capacity. 580 gallons fresh water capacity. 800 cubic ft. foamed and fiberglass fish hold. Simplex gurdies, stainless steel davits and aluminum trolling poles. Anchor winch and gear. ComNav autopilot. Apitong deck. Vessel has a yacht like finish inside. Asking $485,000.
$240,000
thumbnail CR15-012  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1949    Length: 48.6    Hull: Wood    Builder: K Carter    Location: California
48.6'x14'x6' combination California troll/crab package built in 1949 by K Carter. GMC 471 main rated at 190 hp. Capitol gear. Nassau 8 kw generator. 5,000 pound crab tank with a hydraulic lift. 4,000 pound insulated slush salmon tank. Stainless steel hayrack with 3 spool Kolstrand gurdies. Electronics include a Furuno 1650 GPS, Icom VHF, Furuno 48 mile radar, Raytheon sounder and a ComNav autopilot. Comes with a CA 250 pot permit, approximately 250 pots and a CA salmon troll permit. Asking $240,000.
$425,000
thumbnail CR15-011  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1979    Length: 89    Hull: Steel    Builder: Halls Mill    Location: Alabama
89'x22.4'x11.2' combination vessel in 1979, but completely rebuilt including 60% hull re-plating. Cat 3412 main rated at 600 hp, recently rebuilt with only 600 hours. Cummins 100 kw with 163 hours, Cummins 80 kw with 2.9 hours and Isuzu 12.5 kw generator. 3,500 cubic ft. fish hold. Complete refrigeration package with two screw compressor. All new safety gear. Electronics include GPS, VHF, Furuno radar, plotter and autopilot. Has 5 staterooms with 10 berths. Asking $425,000.
$265,000
thumbnail CR15-010  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1996    Length: 29.7    Hull: Fiberglass    Builder: Little Hoquiam    Location: Oregon
29.7'x11.7'x2.9' longline/crab/troll package with permits included. Built in 1996 by Little Hoquiam. Cummins main rated at 220 hp. Twin Disk 502 2:1 gear. 250 gallons fuel capacity in two aluminum tanks. 450 cu. ft. hold, packs 9,000# crab. Crab block and longline hauler with stainless steel shivs and 3 spool Kohlstrand troll gurdies. Longline gear, approximately 275 34" crab pots and full compliment of salmon trolling gear. Other equipment included is a 13'x8' freezer, 16' 48 crab pot flatbed trailer and lots of spare parts and additional equipment. Electronics include GPS system, (2) VHF, VMS, Furuno 16 mile radar, Furuno 1,000W sounder, plotter, Raymarine autopilot and 3,000W inverter.Permits include are OR 300 pot crab, OR salmon troll, and OR live fish endorsed permits, asking $265,000. Also available, but not included, is a Tier III longline endorsed permit with all gear.
$200,000
thumbnail CR15-008  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1979    Length: 32    Hull: Fiberglass    Builder: Uniflite    Location: California
32'x11.5'x5.3' crabber/troller built by Uniflite in 1979. Includes CA 300 pot crab permit. 3208 CAT 210 hp main with low hours. Twin Disk 2:1 gear. 8kw gen set. Rigged for troll and crab. 10 ton RSW and coils refrigeration system. Electronics include (4) GPS, (2) VHF, (2) radar, sounder, plotter, and auto pilot. Asking $200,000 with crab permit.
$380,000
thumbnail CR15-009  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1992    Length: 38    Hull: Fiberglass    Builder: Main Marine    Location: California
38'x13.8'x4' fiberglass crabber/troller, built in 1992 by Main Marine. Twin Cummins 6CTA8-3 rated at 255 hp ea. ZF 311A gears. 5 kw Cummins generator. Packs 6,000# in 6 fish holds. Deck gear includes crab block, longline hauler, and 3 spool Simplex gurdies. Electronics include GPS, VHF, radar, (2) video sounders, ComNav autopilot. 450 gallons fuel, 40 gallons water. Nice large open deck. Aluminum bulwarks and picking boom. Nice boat. Complete package including 400 pot CA crab permit, OR and CA salmon troll licenses, and approximately 300 pots. Asking $380,000 for the works.
$85,000
thumbnail CR15-007  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1989    Length: 48    Hull: Fiberglass    Builder: Growler Boat Works    Location: Alaska
48'x15.5'x7.5' combination crab/shrimp/sternpicker built in 1989 by Growler Boat Works. Twin Detroit 453 mains, Twin Disc 506 gears. 800 gallons fuel capacity. Yamaha 2.5 kw gas generator, Honda 1 kw gas generator. 12,000 lbs capacity. Kolstrand hydraulic block. Electronics include a Raytheon radar with split screen GPS, Furuno GP-32 GPS, Furuno sounder, (2) VHF and a Trace inverter. Price reduced to $85,000.
$249,000
thumbnail CR15-006  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1989    Length: 32    Hull: Fiberglass    Builder: Sunnfjord    Location: California
32'x13' fiberglass troller, crab, tuna vessel built by Sunnfjord in 1989. John Deere 6-359 120hp main with Twin Disk gear. Rigged with 15" crab block, 3-spool gurdies, tuna puller, hydraulic picking boom, and hydraulic anchor winch. Electronics include GPS, (2) VHF, SSB, radar, sounder, plotter, 2-meter, and auto pilot. Also CA salmon troll and CA 350 pot dungeness crab permits are included in the asking price of $249,000.
$80,000
thumbnail CR15-005  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Length: 35    Hull: Fiberglass    Builder: unknown    Location: British Columbia
35'x12'x4' fiberglass crabber/prawn vessel. Volvo 71 main rated at 400 hp with only 200 hours. 16 know cruise. 14” hydro slave hauler, davit and sorting table. Electronics include GP-32 GPS, Standard Horizon VHF, Tough Book computer, Furuno radar, Furuno sounder, Nobeltech plotter and Xantrex 2000 watt inverter. Asking $80,000.
$130,000
thumbnail CR15-004  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1991    Length: 30    Hull: Aluminum    Builder: AK Workboats    Location: British Columbia
30'x10' aluminum Puget Sound crabber built by AK Workboats in 1991. Yanmar 6LYA rated at 315 hp. Arneson ASD8 surface drive. 20 knot plus cruise. Bow thruster. Crab davit, 12’ Hydroslave crab block, landing table, Diamond Sea Glaze windows, Webasto forced air heater and 6 man life raft. Electronics include a Furuno FCV-620 sounder, Furuno 16 mile radar, Standard HZ GPS, Standard VHF and an inverter. Asking $130,000.
$450,000
thumbnail CR15-002  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1982    Length: 36    Hull: Steel    Builder: Steel Boats    Location: California
36'x12.5'x6.4' 400 pot California crab salmon package built in 1982. GMC 471 main rated at 110 hp. Recently rebuilt Velvet drive gear. New Twin Disc gear is included. 12,000# capacity in a fiberglass fish hold. Approximately 375 pots, Warren Junes 19” crab block, aluminum dump box, new stainless steel salmon hayrack with gurdies and aluminum poles. Electronics include GPS, Standard Horizon VHF, ComNav autopilot, loud hailer, new Hazen Measure for setting pots, new plotter with AIS and radar overlay. 400 pot CA crab and CA salmon permits included. Boat has been completely gone through in the last 2 years. Asking $450,000.
$100,000
thumbnail CR15-003  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1973    Length: 52    Hull: Fiberglass    Builder: Wakefield Sons, Inc.    Location: Alaska
52'x15.8'x8.5' fiberglass combination longline, crab, and cod jigging vessel built by Wakefield Sons Inc. in 1973. Detroit 8V71NA main rated a 300 hp. Twin Disc 509 gear. Yanmar 13kw generator. Yahmaha generator. 1,350 gallons fuel capacity. (3) jigging machines, Kolstrand longline hauler, Westort 17" line hauler, Marco crab hauler, steel pipe davit with hydraulic ram, KEM longline reel. Electronics include Raytheon radar, Furuno GPS, Furuno plotter, Acer computer with Nobeltec navigation software, JRC sounder and ComNav 1001 autopilot. Asking $100,000.
$1,500,000
thumbnail CR14-024  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1989    Length: 58    Hull: Steel    Builder: Fred Wahl    Location: Alaska
57.8'x18.5'x8.7' Fred Wahl built combination vessel built in 1989. Cummins NTA 855 main with 3,300 rebuilt hours. Twin Disc gear. Isuzu 4BG1-B 45kw and Isuzu A 4JG1 25kw generators. IMS 18 ton RSW system. 90,000# capacity in two tanks. Bait fish hold is outfitted with freezer unit. (2) cargo booms and main boom with winches. Electronics include a Furuno GPS, Olex bottom mapping navigation system, PC computer with Rose Point navigation system, Furuno color sounder, Tracphone with dispatch, Simrad autopilot and Furuno satellite compass. Also available but not included is a longline setup with full shelter deck and 148 6x6 cod pots, hauler, bait chopper and all miscellanous items for cod fishing. Very clean vessel with continuos upgrades. Asking $1,500,000.
$25,000
thumbnail CR14-022  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1938    Length: 52    Hull: Wood    Builder: Hanson Boat Shop    Location: Alaska
52'x15'x8' combination seiner/troller/crabber built in 1938 built in Hanson Boat Shop. Detroit main rated at 180 hp. Twin Disc 509 gear. 40,000 lbs. salmon capacity and 5,000 lb crab tank capacity. Picking boom with winch. Aluminum hayrack and 3 spool Kolstrand gurdies. Electronics include Furuno radar, VHF Furuno GPS, Sitex sounder, ComNav 2001 autopilot and 3000 watt inverter. Price reduced to $25,000, all offers considered.
$150,000
thumbnail NF14-001  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1942    Length: 125    Hull: Steel    Builder: US Navy    Location: Oregon
THIS VESSEL CANNOT FISH LEGALLY WORLD WIDE, INCLUDING TENDERING AND CHARTER FISHING OPERATIONS AND CANNOT BE DELETED FROM US REGISTRY. 126'x30'x12.5' steel crabber/tender, built in 1942 by US Navy and converted to Bering Sea crabber. Repowered w/ Cat 3412 mains with approximately 12,000 hours each. Cat 3306 190 kw, GMC 8V71 100 kw and new kw gen sets. (2) fish holds, tanked w/ RSW. Complete electronics with many backups. 30,000 gallon fuel capacity. (2) deck cranes. Price reduced to $150,000.
$1,400,000
thumbnail CR14-021  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1978    Length: 105    Hull: Steel    Builder: Sundial Marine    Location: Alaska
105'x26'x8.7' house aft crabber/tender, built in 1978 by Sundial Marine. Twin Cummins NTA-14-M Tier III mains rated at 425 hp each. (2) Cummins 855 190 kw gen sets, Detroit 4-71 40 kw gen set. Packs 250,000+ pounds of salmon w/ (2) RSW systems. Comes with full tendering setup. Available with appr. 250 7x pots and BS and WG LLP with P-cod pot endorsement. Asking $1,400,000 for boat and LLP plus $500/pot. Call for details.
$40,000
thumbnail CR14-020  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1952    Length: 41    Hull: Wood    Builder: unknown    Location: Washington
41'x11.9'x6.6' combination troll/crab/longline vessel built in 1952. GMC 453 main rated at 140 hp. Twin Disc MG 5050 gear. 14,000 lbs iced salmon capacity. 15” Northwest crab block, davit and crab tank insert. (2) 3 spool Kolstrand gurdies. 15 skate longline drum. Electronics include an Icom VHF, standard VHF, Furuno radar, Furuno GPS, Garmin GPS, Furuno sounder, ComNav 1001 autopilot and Gateway laptop with navigation software. Alaska power troll permit available at market value. Asking $40,000.
$449,500
thumbnail CR14-019  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1975    Length: 72.7    Hull: Steel    Builder: CD Carnes Welding Service    Location: Oregon
72.7'x18.2'x11' combination crab, tuna, longline, tender built in 1975 by CD Carnes in Morrow Bay, CA. Lengthened 10 feet in 1990 by Fisherman’s Boat Yard. John Deere 6125 12.5 liter 400 hp main. Isuzu 4BG1 40kw and Mitsubishi 35kw generators. Three fish holds have 35 ton tuna capacity. 15 ton blast system, 18 ton plate freezer compressor, bait tank RSW system and a large deck mounted plate freezer system. 5,000 gallon fuel capacity, 2,000 fresh water capacity. Electronics include (3)VHF, satellite phone, Navtrac GPS, Simrad plotter, Wesmar sonar, ComNav autopilot and a Skymate VMS. 5 spool gurdies, single tuna puller, aluminum trolling poles, bait chopper, crab block and davit. Price reduced to $449,500.
$20,000
thumbnail CR14-018  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1943    Length: 42.4    Hull: Wood    Builder: Higgins    Location: California
42.4'x10'x4.5' wood troller/crabber built in 1943 by Higgins. GM 671 main with 160 hp. 2,300 hours on rebuild. All new stainless exhaust. 1.6 gallon per hour fuel consumption. 5 ton ice hold, crab insert. New aluminum poles and mast. Bulworks new in 2012. 3-spool gurdies with new wire. 4-man life raft new in 2012. Electronics include GPS, (2) VHF, CB, and radar. CA salmon troll permit included!! Must sell, reduced to $20,000.
$275,000
thumbnail CR14-017  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1980    Length: 48    Hull: Steel    Builder: Troyer    Location: Alaska
48'x16'x8.8' steel crabber/ longliner with Marco auto longline system built by Troyer in 1980. Cummins 855 main rated 275 hp. Twin Disc 509 gear. John Deere 4045 40kw generator. 40,000 pounds fish hold capacity. 18 ton IMS rsw system. Marco Auto longline system, crab block, king coiler, aluminum shelter deck, (2) booms and bait chopper. Electronic inclue Garmin GPS, (2) VHF, SSB, Dell desktop computer, Koden radar, Furuno sounder, MaxSea navigation software, satellite compass, Olex transducer installed in 2014 and Faria VMS unit. Contact us for recent survey. Price reduced from $390,000 to $275,000!
$85,000
thumbnail CR14-016  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1976    Length: 38    Hull: Fiberglass    Builder: Modutech    Location: California
38’x12’6” fiberglass Modutech troller/crabber, built in 1976. Cummins 285 hp 9 liter diesel, new in 2011, appr. 1,500 hrs., burn 3 gph@8 kts. ZF gear new in 2011. Both installed in 2013. Electronics inclde GPS, VHF, polotter, sounder, autopilot, computer, and more. Comes with trolling poles, gurdies, and crab davit. Packs 4,000# crab. Asking $85,000.
$269,500
thumbnail featured listing CR14-014  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1953    Length: 65    Hull: Steel    Builder: National Ship and Steel    Location: Oregon
65'x17.9'x11.2' steel tuna freezer vessel built by National Ship and Steel Building to military specifications for the US Army as a towing vessel. Cummins model 855 300 hp main with Twin Disc MG-514-C, 3.5:1 gear. 50 kw John Deere/MER aux. 6,250 gal. fuel capacity in (8) tanks. 1,450 gal. water capacity with 150 gal/day water maker. 1,300 cu. ft. freezer hold. (2) 75 cu. ft. brine/bait tanks on deck. RSW for brine tanks and blast freeze in freezer hold. Approximately 4,500 mile range at full throttle. Complete electronics package including sonar. Call for complete current survey. Price reduced to $269,500.
$168,000
thumbnail CR14-010  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1963    Length: 59.1    Hull: Steel    Builder: Capel Marine    Location: Washington
59.1’x19.7’x9.2’ crabber/tuna built in 1963 by Capel Marine. Cat 342 main rated at 280 hp. Twin Disc 514 gear. John Deere 85 kw genset. 60,000# capacity in 2 fish holds. (2) tuna pullers, side, corner, stern racks, bait tanks and bait poles. Hydraulic pot pump, 3 hoses, Astoria block, davit and dump box. Electronics include (3) GPS, (2) VHF, SSB, laptop with Nobeltech, 16 mile radar, Si-Tex sounder and ComNav autopilot. Asking $168,000.
$800,000
thumbnail CR14-013  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1933    Length: 113    Hull: Steel    Builder: US Navy    Location: Washington
112’x30.5’x12.5’ combination vessel built by the US Navy in 1933. Twin Cat 353 mains rated at 850 total hp. (2) Cat 3306 175 kw generators. 4 insulated fish holds totaling 10,200 sq ft. 100 ton RSW system. Ryan fish pump (new in 2013). Abundant electronics. 38,000 gallons fuel capacity. 10,000 gallons water with water maker. 8 berths. Vessel does not have its Coastwise Trade and cannot legally tender fish but, it did have a contract in Bristol Bay as a net barge and chilled water for other tenders. Asking $800,000.
$149,000
thumbnail CR14-009  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 2004    Length: 32    Hull: Aluminum    Builder: Western Fabrication    Location: Washington
32'x10'x3' combination crab/longline/tuna vessel built in 2004 by Western Fabrication. Volvo Penta D4 main rated at 225 hp with only 326 hours. Dual prop outdrive. Honda 9.9 trolling motor. 120 gallon fuel capacity. Tuna poles, longline chute, crab block, davit and landing box. Electronics include an Icom VHF, Lowrance sounder, Garmin plotter, VMS. Easy loader trailer. Price reduced to $149,000.
$160,000
thumbnail CR14-003  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 2012    Length: 35.5    Hull: Aluminum    Builder: LCS Performance    Location: Washington
35.5’x10.6’x2.5’ high speed crab vessel built in 2012 by LCS Performance. Suzuki 300 hp outboard. 31 knots WOT. Suzuki 20 hp outboard. Honda 390 GX power pack. 12” Hydroslave crab block, ram davit. 300 gallons fuel capacity. Electronics include an Icom VHF, Furuno radar, Furuno plotter and a Standard Horizon GPS. Asking $160,000.
$1,500,000
thumbnail CR13-034  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1966    Length: 58    Hull: Steel    Builder: Hydraulic Supply    Location: Alaska
58'x24'x10' sponsoned combination seiner/crabber/dragger built in 1966 by Hydraulic Supply. In 2009 a new house and other major wiring and engine rebuild performed. Cat 3408 B main rated at 480 hp. Twin Disc gear. John Deere 6081 55kw and Isuzu 35kw generators. 120,000 lbs fish hold capacity. 18 ton IMS system. Electronics include GP 70 and Satellite compass, (2) VHF, SSB, computer, Furuno radar, Furuno sounder, ComNav autopilot, AIS and engine room and deck cameras. Asking $1,500,000
$450,000
thumbnail CR13-032  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1974    Length: 40    Hull: Steel    Builder: Donald G Barber    Location: Oregon
40'x13'x6.3' steel combination crabber, tuna/salmon troller, with permits, built in 1974, bulbous bow added in 2015. 671 Detroit main rated at 174 hp. 1000 gallons fuel capacity. Isuzu 9 kw generator with new engine in 2015. 16 ton fish hold capacity. Crab block, tuna/salmon gurdies, crab tank insert, crab pots, longline puller and tubs. Electronics include GPS, (3) VHF, (2) radars new in 2015, (1) sounder, (1) plotter, inverter and autopilot. Package includes 300 pot OR crab permit, 300 pots and OR/CA salmon troll permits. Asking $450,000.
$950,000
thumbnail CR13-031  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1967    Length: 160    Hull: Steel    Builder: Zigler    Location: Washington
160'x36' ex-supply vessel, built in 1967 by Zigler, converted to crab in 1990. Vessel has undergone major steel work, needs completion of refitting. Twin Cat 398 mains rated at 950 hp, partial rebuilds need completion. (2) 500 kw Detroit 16V92 gen sets, (1) 75 kw 4-71 gen set. 13,600 cu ft. freezer holds. 61,000 gal fuel and 28,000 water capacities. Interior needs refitting. Call for details. Asking $950,000.
$1,200,000
thumbnail CR13-023  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1979    Length: 57.9    Hull: Steel    Builder: Union Bay Boat Works    Location: Alaska
57.9'x27'x10' steel longliner that can easily be converted to seining, crabbing and pot cod. Originally built in 1979 and extensively rebuilt in 2007, including a bulbous bow and sponsons. Cummins KTA 19-M3 main rated at 640 hp. John Deere 50 kw and 27 kw generators. Teknotherm RSW. 95,000 lbs capacity in two fish holds. Full aluminum shelter deck, Marco autobaiter. Stainless hydraulic plumbing. Captains stateroom w/full head on bridge. Full shop and bait freezer in pilot house sponsons. Extensive electronics package including satellite compass, NavNet navigation system, Nobeltec navigation software, Furuno color video sounder and ECC Globe terrain building software. Top of the line vessel with numerous upgrades and recent shipyard work. Asking $1,200,000. Two LLPs for CG HAL, WG HAL-Pot, BS and AI available.
$425,000
thumbnail CR13-019  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1986    Length: 68    Hull: Steel    Builder: Chauvin    Location: Washington
68'x20'x7' steel crabber/tender built by Chauvin in 1986. Cummins NTA 855 main, 360 hp. Twin Disc 514 4.5:1 gear. GMC 3-71 30kw aux, John Deere 40kw aux. (2) Copeland 15 ton compressor for RSW. 55,000 capacity in one tank. Completely rigged with all the gear for crab, and tendering. 2,600 gallons water, 6,500 gallons fuel capacities. Aluminum deck gas tank for transfer during tendering. Up to 90 days tender contract available to qualified buyer. Electronics include AIS, MSAT sat pn, satellite compass auto pilot, (2) GPS, VHF, SSB, plotter, radar, sounder, Trac phone, and VMS. WA 500 pot permit available for sale. Asking $425,000.
$210,000
thumbnail CR13-018  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 2002    Length: 52    Hull: Fiberglass    Builder: Guimond    Location: Hawaii
52'x17'9" fiberglass tuna longliner built by Guimond in 2002. Twin Cummins QSM11 600hp mains with ZF311A 2:1 gears. 30 knots WOT. John Deere 40kw aux. 1,800 gallon fuel capacity in (5) tanks. 10 fish holds pack 25,000 #'s in slush ice. Price Reduced to $210,000.
$2,680,000
thumbnail CR13-017  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1991    Length: 58    Hull: Fiberglass    Builder: Delta    Location: Washington
Exceptionally clean 58’ “wide body” Delta built in 1991. Can be rigged for seining, dragging and pot fishing. Cat 3412 main rated at 650 hp. Twin Disc 517 gear. 5 blade propellor. Bulbous bow with bow thruster. Cat 3304B 50kw generator with double hydraulic pump. Isuzu 4BG1 35kw generator. 30 hp carrier RSW system. 165,000 capacity in 2 fish holds. Stainless steel tubing hydraulics lines. Stern ramp for trawling with plug insert. Free standing mast, twin picking booms,slider main boom with slider and (2) gilson winches. Electronics package. Asking $2,680,000.
$120,000
thumbnail CR13-016  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1991    Length: 32    Hull: Aluminum    Builder: R.C. Shreib Fisheries    Location: Alaska
32'x13.8'x3.6' sternpicker/crabber built in 1991 by R C Shreib. Lugger 6125AL main rated at 400 hp. ZF 1.5:1 gear. Power roller, crab davit, 12" Hydro Slave pot puller and free standing mast. Thermal Tec 7.5 ton RSW system. Electronics include an Uniden VHF, Data Marine plotter, Icom 2 meter, Furuno radar, Robertson autopilot and watch alarm. Price reduced to $120,000.
$650,000
thumbnail featured listing CR13-002  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 1980    Length: 104    Hull: Steel    Builder: Bender    Location: Massachusetts
104’x28’x12’ steel crabber / tender, built in 1980 by Bender. Cat 3508TA main rated at 775 hp, Cat 3406B 135 kw and John Deere 99 kw. Wesmar bow thruster. Two fish holds total appr. 4,675 cu. ft. No RSW, but can be easily configured to a RSW system. Bait freezer on deck. 26,513 gallons fuel, 1,413 water. (2) Independent navigation computers with Win-Plot navigation software. Each computer is equipped with battery backup and (2) separate and selectable GPS data streams. Furuno 1411 73 mile radar, Furuno 1800 32 mile radar, Furuno 292 color echo sounder, Furuno GPS receiver, Northstar 6000i GPS receiver, Simrad AIS receiver, Simrad AP50 autopilot, Type DT-7, Icom 700 single side band radio, Icom VHF radio, Uniden VHF radio. Vessel currently on the East Coast. Seller will consider partial delivery options. Price reduced to $650,000.
$99,500
thumbnail CR13-001  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Length: 28    Hull: Fiberglass    Builder: Fiberform    Location: Washington
28’x10.5’ completely refurbished Fiberform fast crabber with new main engine. New Volvo main engine rated at 330 hp. 40 kts maximum speed, cruise at 28 kts. 98 gallons fuel capacity. V-berth. Garmin GPS. Crab davit, block, aluminum swim step and aluminum hand railing around the vessel. 2010 16,500 triple axle Tuf Trailer. The boat was completely rebuilt from the hull up, everything is new. Excellent Puget Sound crab skiff. Price reduced to $99,500.
$22,000
thumbnail CR11-008  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Length: 26    Hull: Fiberglass    Builder: Seasport/Buffalo    Location: Washington
26'x8’ crabber, Seasport hull, finished by Buffalo Boats. Only one season on new Chev 350-300 "Stroker" engine. Cruises at 18-20 knots @ 3400 RPM. Electronics include Furuno radar, LCD sounder, VHF, and marine AM/FM CD stereo. Crab davit, one season on 12" Hydro Slave puller. Life ring, survival suit, 4 props and other extras. Forepeak has room for bunks to be installed. Turn-key boat ready to fish. Trailer included. Asking $22,000.
$2,300,000
thumbnail CR10-003  Crabbers You must be logged in to watch items for updates. You can click here to go to the Login / Registration page...
Year: 2007    Length: 63    Hull: Steel    Builder: Van Peer    Location: Oregon
63’x25’ steel Jensen design crabber / longliner, built in 2007 by Van Peer. Cummins K19M main rated at 680 hp. (2) John Deere 100 kw gen sets. Bow thruster. (2) stainless steel lined fish holds, packs appr. 250,000# with 40 ton RSW system and spray brine in one hold. Deck crane. Electronics include 72 mi Furuno radar, SEA 222 SSB, (2) GPS, autopilot, and more. Coastal top tier black cod permit, WA, OR, and CA crab permits available to buyer. Price reduced to $2,300,000, seller is looking for offers.
Web Design, 3 Crown Creative